DPLL(8)

NAME
dpll - Digital Phase Locked Loop (DPLL) subsystem management

SYNOPSIS
dpll [ OPTIONS ] device { COMMAND | help }

dpll [ OPTIONS ] pin { COMMAND | help }

dpll [ OPTIONS ] monitor
OPTIONS := { -V | --Version | -j | --json | -p | --pretty | -t | --timestamp | --tshort }

DESCRIPTION
The dpll utility is used to configure and monitor Digital Phase Locked Loop (DPLL) devices and pins. DPLLs are used for clock synchronization in various hardware, particularly in telecommunications and networking equipment. A DPLL device can lock to one or more input pins and provide synchronized output. Pins can be physical external signals (like GNSS 1PPS, SyncE), or internal oscillators.

OPTIONS

-V, --Version
    Print the version of the dpll utility and exit.

-j, --json
    Output results in JavaScript Object Notation (JSON).

-p, --pretty
    When combined with -j, generates a pretty JSON output with indentation and newlines for better human readability.

-t, --timestamp
    When used with the monitor object, print a Timestamp: line before each received notification, in the same format used by ip monitor.

--tshort
    Like -t, but emits a more compact, ISO 8601 inline prefix “[YYYY-MM-DDTHH:MM:SS.uuuuuu]” in front of each notification instead of a separate Timestamp: line.

DEVICE COMMANDS

  dpll device show [ id ID ] [ module-name NAME ] [ clock-id ID ] [ type TYPE ] [ mode MODE ] [ lock-status STATUS ]
Display information about DPLL devices. If no arguments are specified, shows all devices in the system.

id ID
    Show only the device with the specified numeric identifier.

module-name NAME
    Show only devices provided by the specified kernel module.

clock-id ID
    Show only devices with the specified 64-bit clock identifier.

type TYPE
    Show only devices of the specified type: pps or eec.

mode MODE
    Show only devices in the specified operating mode: manual or automatic.

lock-status STATUS
    Show only devices with the specified lock status: unlocked, locked, locked-ho-acq, holdover.

Output includes:

    •   Device ID

    •   Module name providing the device

    •   Clock ID (unique identifier)

    •   Operating mode (manual, automatic)

    •   Lock status (unlocked, locked, locked-ho-acq, holdover)

    •   Lock status error (if present)

    •   Clock quality level (if supported)

    •   Temperature (if supported)

    •   Type (PPS or EEC)

    •   Supported modes

    •   Phase offset monitor status (enable/disable)

    •   Phase offset averaging factor

    •   Frequency monitor status (enable/disable)

  dpll device set id ID [ PARAMETER VALUE ] ...
Configure DPLL device parameters.

id ID
    Specifies which device to configure (required).

mode { automatic | manual }
    Set the operating mode of the DPLL device. In automatic mode, the DPLL autonomously selects the best available input source based on priority and quality. In manual mode, the input source must be explicitly configured and the DPLL will not automatically switch sources.

phase-offset-monitor { enable | disable }
    Enable or disable phase offset monitoring between the device and its pins. When enabled, the kernel continuously measures and reports phase differences.

phase-offset-avg-factor FACTOR
    Set the averaging factor (1-255) applied to phase offset calculations. Higher values provide smoother but slower-responding measurements.

frequency-monitor { enable | disable }
    Enable or disable frequency monitoring on the device. When enabled, the kernel continuously measures and reports actual pin frequencies, which can be read via the measured-frequency field in pin show output.

  dpll device id-get [ module-name NAME ] [ clock-id ID ] [ type TYPE ]
Retrieve the device ID based on identifying attributes. Useful for scripting when you need to find a device's numeric ID. At least one attribute should be specified to identify the device.

module-name NAME
    Kernel module name.

clock-id ID
    64-bit clock identifier in decimal or hex (0x prefix).

type TYPE
    Device type: pps or eec.

PIN COMMANDS

  dpll pin show [ id ID ] [ parent-device DEVICE_ID ] [ parent-pin PIN_ID ] [ module-name NAME ] [ clock-id ID ] [ board-label LABEL ] [ panel-label LABEL ] [ package-label LABEL ] [ type TYPE ] [ direction DIR ] [ state STATE ] [ operstate OPERSTATE ]
Display information about DPLL pins. If no arguments are specified, shows all pins in the system.

id ID
    Show only the pin with the specified numeric identifier.

parent-device DEVICE_ID
    Show only pins that have the specified DPLL device as a parent.

parent-pin PIN_ID
    Show only pins that have the specified pin as a parent (mux pins).

module-name NAME
    Show only pins provided by the specified kernel module.

clock-id ID
    Show only pins with the specified 64-bit clock identifier.

board-label LABEL
    Show only pins with the specified board label.

panel-label LABEL
    Show only pins with the specified panel label.

package-label LABEL
    Show only pins with the specified package label.

type TYPE
    Show only pins of the specified type: mux, ext, synce-eth-port, int-oscillator, gnss.

direction DIR
    Show only pins that have a parent-device relationship with the specified direction: input, output. When combined with parent-device, only the specified parent-device relationship is checked.

state STATE
    Show only pins that have a parent-device relationship with the specified state: connected, disconnected, selectable. When combined with parent-device, only the specified parent-device relationship is checked.

operstate OPERSTATE
    Show only pins that have a parent-device relationship with the specified operational state: active, standby, no-signal, qual-failed. When combined with parent-device, only the specified parent-device relationship is checked.

Output includes:

    •   Pin ID

    •   Module name

    •   Clock ID

    •   Board label (hardware label from device tree or ACPI)

    •   Panel label

    •   Package label

    •   Pin type (mux, ext, synce-eth-port, int-oscillator, gnss)

    •   Configured frequency and supported frequency ranges

    •   Measured frequency in Hz (when frequency monitoring is enabled)

    •   Capabilities (state-can-change, priority-can-change, direction-can-change)

    •   Phase adjustment range, granularity, and current value

    •   Fractional frequency offset

    •   Parent device relationships (direction, priority, state, phase offset)

    •   Parent pin relationships

    •   Reference sync information

    •   Esync frequency and pulse support (if applicable)

  dpll pin set id ID [ PARAMETER VALUE ] ...
Configure DPLL pin parameters. Multiple parameters can be specified in a single command.

id ID
    Specifies which pin to configure (required).

frequency FREQ
    Set pin frequency in Hz. The pin must support the specified frequency (check frequency-supported ranges in pin show output).

phase-adjust ADJUSTMENT
    Set phase adjustment in picoseconds. This value fine-tunes the phase of the output signal. Negative values shift the phase backwards, positive values shift it forwards. The value must be within the phase-adjust-min and phase-adjust-max range.

esync-frequency FREQUENCY
    Set enhanced SyncE (Synchronous Ethernet) frequency in Hz for capable pins.

parent-device DEVICE_ID [ direction DIR ] [ prio PRIO ] [ state STATE ]
    Configure the relationship between this pin and a parent DPLL device.

    direction { input | output }
        Set the pin's direction relative to the parent device.

    prio PRIORITY
        Set priority (0-255) for this pin on the parent device.

    state { connected | disconnected | selectable }
        Set the pin's state on the parent device.

parent-pin PIN_ID [ state STATE ]
    Configure the relationship to a parent pin.

reference-sync PIN_ID [ state STATE ]
    Configure reference sync relationship with another pin.

  dpll pin id-get [ SELECTOR ] ...
Retrieve a pin ID based on identifying attributes.

module-name NAME
    Filter by kernel module name.

clock-id ID
    Filter by 64-bit clock identifier.

board-label LABEL
    Filter by board label (hardware identifier).

panel-label LABEL
    Filter by panel label.

package-label LABEL
    Filter by package label.

type TYPE
    Filter by pin type: mux, ext, synce-eth-port, int-oscillator, gnss.

MONITOR COMMAND

  dpll monitor
Monitor DPLL subsystem events in real-time. Displays notifications about:

    •   Device creation, deletion, and configuration changes

    •   Pin creation, deletion, and configuration changes

    •   Lock status changes

    •   Phase offset updates

    •   Frequency changes

Events are prefixed with their type: [DEVICE_CREATE], [DEVICE_CHANGE], [DEVICE_DELETE], [PIN_CREATE], [PIN_CHANGE], [PIN_DELETE].

Press Ctrl+C to stop monitoring.

EXAMPLES

  Show all DPLL devices
dpll device show

  Show specific device in JSON format
dpll -j device show id 0

  Set device 0 to manual mode
dpll device set id 0 mode manual

  Enable phase offset monitoring on device 0
dpll device set id 0 phase-offset-monitor enable

  Enable frequency monitoring on device 0
dpll device set id 0 frequency-monitor enable

  Show all EEC devices
dpll device show type eec

  Show devices from specific module in JSON
dpll -jp device show module-name ice

  Show all pins
dpll pin show

  Show all GNSS pins
dpll pin show type gnss

  Show GNSS pins from specific module
dpll pin show type gnss module-name ice

  Show pin with pretty JSON output
dpll -jp pin show id 5

  Show connected input pins on device 0
dpll pin show parent-device 0 direction input state connected

  Set pin frequency to 10 MHz
dpll pin set id 0 frequency 10000000

  Configure pin relationship to parent device
dpll pin set id 1 parent-device 0 prio 10 direction input state connected

  Adjust phase by -1000 picoseconds
dpll pin set id 2 phase-adjust -1000

  Set multiple pin parameters at once
dpll pin set id 3 frequency 10000000 phase-adjust -1000

  Monitor DPLL events
dpll monitor

  Monitor events in JSON format
dpll -jp monitor

  Get device ID by module name
dpll device id-get module-name ice

  Get pin ID by board label
dpll pin id-get board-label GNSS-1PPS

PHASE ADJUSTMENT
Phase adjustment is specified in picoseconds (1e-12 seconds) and allows fine-tuning of signal phase. This is crucial for precise time synchronization applications like 5G networks and high-frequency trading.

Important considerations:

    •   Check phase-adjust-min and phase-adjust-max before setting values

    •   Some hardware requires values to be multiples of phase-adjust-gran

    •   Negative values shift phase backwards (earlier in time)

    •   Positive values shift phase forwards (later in time)

    •   The kernel validates all phase adjustment requests

CAPABILITIES
Pins may have various capabilities that determine which operations are allowed:

state-can-change
    The pin's state (connected/disconnected/selectable) can be modified.

priority-can-change
    The pin's priority can be modified. This may apply to top-level priority or priority within parent-device relationships.

direction-can-change
    The pin's direction (input/output) can be modified.

Use dpll pin show to check which capabilities a pin supports before attempting configuration changes.

EXIT STATUS

0   Success

1   Failure

NOTES

•   The DPLL subsystem requires kernel support (CONFIG_DPLL=y or m)

•   Hardware support varies by device and driver

•   Some operations require specific hardware capabilities

•   Phase offset values are measured by hardware and cannot be set directly

•   Changes to device/pin configuration may affect system clock synchronization

SEE ALSO
ip(8), devlink(8), ethtool(8)

Linux kernel documentation: Documentation/driver-api/dpll.rst

Netlink specification: Documentation/netlink/specs/dpll.yaml

AUTHOR
dpll was written by Arkadiusz Kubalewski, Vadim Fedorenko, and others. This manual page was written by Petr Oros.

REPORTING BUGS
Report bugs to <netdev@vger.kernel.org>